NSC18-WNPaN/TilTNeTWorkCamera uSermaNual MODEL550857 INT-550857-UM-0709-01
10SOFTWARE INSTALLATION4. With the General menu tab/screen displayed, select “Internet Protocol (TCP/IP),”then click “Properties.”
11SOFTWARE INSTALLATION2.2 Using the Admin Utility to Locate the CameraIf you can’t connect to the camera using the above procedure, you can use the
12SOFTWARE INSTALLATION2.WhentheSelectDestinationLocationscreendisplays,click“Next”to use the default installation folder and continue, o
13SOFTWARE INSTALLATION4.WhentheReadytoInstallscreendisplays(presentingalltheselected options),click“Install”tocontinueor“Back”to
14SOFTWARE INSTALLATIONAfter the camera’s admin utility is launched, all cameras found on your local area network will be displayed with basic informa
15SOFTWARE INSTALLATIONDHCP — Select to set the camera to automatically obtain an IP address from the DHCP server on the local area network.Manual I
16WEB MANAGEMENT INTERFACEOntheSecurityscreen(above),youcanchangethecamera’snameandpassword(asontheLoginscreen,theusernameisalway
17WEB MANAGEMENT INTERFACE3. The NSC18-WN Pan/Tilt Network Camera requiresaspecialActiveXcontrol(plug-in) in order to work properly. Right-
18WEB MANAGEMENT INTERFACEPan/Tilt Speed—Thisspeciesthemovingspeedwhenyouusethe Pan/Tilt function to point the camera in a different dire
19WEB MANAGEMENT INTERFACE eldofview,selectalowerimagequalitytogetahigherimagerefresh rate.Video Type — Select the video encoding typ
2 CONTENTSTable of CoNTeNTS 1 COMPONENTS & CONNECTIONS ... 6 2 SOFTWARE INSTALLATI
20WEB MANAGEMENT INTERFACE savedimagele(thedefaultlenameisthecurrentdateandtime). Thedefaultdirectoryusedtosaveimageleis“C:\
21WEB MANAGEMENT INTERFACE 3. When the camera is in the position you want, enter a descriptive nameinthe“PositionName”eldandclick“SettoPo
22WEB MANAGEMENT INTERFACEAdd—Clicktoaddanewguardtour(seebelowfordetailedsteps.)Edit—Clicktomodifythesettingsofaconguredtour.S
23WEB MANAGEMENT INTERFACEView Order — Assign this position a number greater than 1 and different from the other positions. Unless Random Order is s
24WEB MANAGEMENT INTERFACENetwork Type — Select “DHCP” to obtain an IP address automatically or“StaticIPAddress”toassignthecameraaxedIPa
25WEB MANAGEMENT INTERFACEAvailable Networks — This is a list of all wireless access points found by the camera. Not all access points will be displ
26WEB MANAGEMENT INTERFACE you want to connect to. If the wireless access point does not use encryption, “Disabled” will be displayed here.
27WEB MANAGEMENT INTERFACE Enable DDNS—Select“Enable”toactivatethefunction;“Disable”to deactivate it.Provider — dyndns.org is currently the
28WEB MANAGEMENT INTERFACEYoucandouble-clicktheicontolaunchInternetExploreranddirectlylog on to the camera’s Web management interface.3.4.5
29WEB MANAGEMENT INTERFACE3.5 Motion Detection SettingsThis function is another useful security tool, as it takes a snapshot when there’smovementin
3INTRODUCTIONiNTroduCTioN Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™ NSC18-WN Pan/Tilt Network Camera, Model 550857.Ideal for home-net
30WEB MANAGEMENT INTERFACESending File Type—Selecttheletypethat’llbesavedwhenmotion is detected. Select “JPEG” and a still picture in JPE
31WEB MANAGEMENT INTERFACERefresh — If the object or objects in the image captured by the camera moveoffscreen,clicktoreloadtheimagesoyouc
32WEB MANAGEMENT INTERFACE3.5.3 E-MailAs mentioned in 3.5.1 Motion Detection, these settings need to be enteredbeforeyoucantakeadvantageofthe
33WEB MANAGEMENT INTERFACE3.5.4 FTP CongurationAs mentioned in 3.5.1 Motion Detection, these settings need to be enteredbeforeyoucanusethe“Se
34WEB MANAGEMENT INTERFACE3.6 System InfoWith four subsections as shown below, all operations-related settings canbeconguredonthismenu’sscreen
35WEB MANAGEMENT INTERFACESet Date/Time manually—Enterthedateintherstthreeboxes,then thetime.TheformatforthedateisYYYY/MM/DD(so
36WEB MANAGEMENT INTERFACE if it responds slowly or erratically.LED Setting — Click “Turn off LED light” if you don’t want anyone in the vieweld
37WEB MANAGEMENT INTERFACECongurethesettingsfortheseuser-levelaccountsontheAccountscreen.Login — Enter a login username.Password — Enter
38WEB MANAGEMENT INTERFACE3.8 SDHCWith three subsections as shown below, this screen presents options forSD-HC(securedigital–highcapacity)card
39SURVEILLANCE SOFTWARESMTP Authentication — Select “Enable” if the SMTP server you’re using requires authentication, then enter the username and pa
4REGULATORY STATEMENTSregulaTory STaTemeNTS EU DECLARATION OF CONFORMITY This device complies with the essential requirements of the R&TTE Directi
40SURVEILLANCE SOFTWARE Startonyourdesktop,thenMyComputer;double-clickontheCD drive where the software CD is located, and double-click th
41SURVEILLANCE SOFTWARE4. When the Select Additional Tasks screen displays, select “Create a desktopicon”and/or“CreateaQuickLaunchicon”asde
42SURVEILLANCE SOFTWARE6.WhentheCompletingtheIPCamSurveillanceSoftwareSetupWizard screen displays, click “Finish” and the Viewer will be a
43SURVEILLANCE SOFTWARE selected camera. Press <Esc> to quit Full Screen mode.Scan (2) — Click to automatically cycle through the views from a
44SURVEILLANCE SOFTWARE position. NOTE: This function is available only with cameras that feature it.Record (7) — Click to begin video recording fr
45SURVEILLANCE SOFTWARE4.3 Conguration Before you can effectively use the Viewer program and all its features, allcamerasconnectedtothenetwork
46SURVEILLANCE SOFTWAREChannel — Select the channel number you want to set.Camera Search — All cameras found on your local network will be displayed
47SURVEILLANCE SOFTWARE4.3.1.2 Schedule RecordingChannel — Select the channel number you want to set.One Time Schedules — This window displays record
48SURVEILLANCE SOFTWARENew / Weekly Schedules — Click to display a new Weekly Schedule screen for the selected camera. Select applicab
49SURVEILLANCE SOFTWAREChannel — Select the channel number you want to set.Mute Audio — Select if the designated camera does support audio but you p
5SAFETY PRECAUTIONSFCC CAUTION Anychangesormodicationsnotexpresslyapprovedbytheparty responsible for compliance could void the user’s author
50SURVEILLANCE SOFTWARE4.3.2 General Options WhenyouclicktheCongurebuttonontheViewercontrolscreenand select“GeneralOptions”fromther
51SURVEILLANCE SOFTWAREScan Time — Enter/selectanamountoftime(inseconds)theViewer will display the view from each camera when the Scan funti
52SURVEILLANCE SOFTWAREE-Mail Subject — Enter the subject of the e-mails being sent.Recipient E-Mail Address(es) — This window displays a list of the
53SURVEILLANCE SOFTWAREtime you attempt to open the Viewer as long as this featureisenabled.(TheAuthentication Required screen at right will disp
54SURVEILLANCE SOFTWARE4.4 Changing the Display Layout The Viewer features eight different display layouts for up to 16 cameras, with each layout pr
55SURVEILLANCE SOFTWARE Layout style 4: 8 Cameras Displays the video of up to 8 cameras. 02 03 01 04 05 06 07 08 Layout style 5: 9 Cameras D
56SURVEILLANCE SOFTWARELayout style 7: 13 Cameras Displays the video of up to 13 cameras. 02 03 01 04 05 06 07 08 09 10 11 12 13 Layout style 8:
57TROUBLESHOOTING5 TroubleShooTiNg Shouldthecameranotfunctionasexpected,seeiftheproblem—along with possible solutions — is listed below.
58TROUBLESHOOTING• Unplugthepoweradapterfromthewallsocketandplugitinagain after 10 seconds, then try to connect to the camera again.•
59SPECIFICATIONS6 SPeCifiCaTioNS Standards• IEEE 802.11b (11 Mbps Wireless LAN)• IEEE 802.11g (54 Mbps Wireless LAN)• IEEE 802.11n Draft 2.
6COMPONENTS & CONNECTIONSFocus adjustment ringLEDsBuilt-in microphoneWireless antenna (1of2)1 ComPoNeNTS & CoNNeCTioNS 1.1 Front and SideW
INTELLINET NETWORK SOLUTIONS™ offers a complete line of active and passive networking products. Ask your local computer dealer for more information or
7COMPONENTS & CONNECTIONS1.2 Back / Connections1. Connect one end of the included Ethernetcable(orasimilarone) to your local area netw
8SOFTWARE INSTALLATION2 SofTWare iNSTallaTioN Oncethecameraconnectionshavebeenmade,launchInternetExploreron your computer and proceed with
9SOFTWARE INSTALLATION2. Double-click the Network Connections icon. 3. Right-click on the Local Area Connection icon, then click “Proper
Comments to this Manuals